|
Notes |
|
|
|
|
I can not reproduce this. The animation is displayed correctly on my machines. |
|
|
|
|
I can reproduce this with all my configurations. With 1.6 the "SUPER" animation is not displayed, while with 1.5 it is. Here is the video, first 1.5 version then 1.6 version of the slave with the same disk:
https://youtu.be/7gDAMJckBRI |
|
|
|
|
Hi,
Tom-Cat has right,
I use WHDLoad 19.0 Beta (19.0.6612) With OS 3.1.4.1 and for WINUAE OS 3.5
I have the same problens on my A500 ACA500Plus, my A1200 & under WINUAE with v1.6 and a fresh insall made from SPS 0816.
When I use the IPF SPS 0816 File converter in HFEv3 file on my Gotek HXC, I can see Super a few seconds after Hang-on,
Best regards,
Pascal |
|
|
|
|
|
sorry it was WHDLoad 19.0.6622, with 19.0.6626 it's the same. |
|
|
|
(0013316)
|
|
StingRay
|
2023-11-19 19:25
(Last edited: 2023-11-19 19:26) |
|
Tom-Cat: Please try attached test slave, it will crash with "illegal instruction" when the "Super" animation should be shown. Please save the coredump and check address $1742 in the .whdl_memory file, is it 0 or does it contain any other value?
You can prevent the crash by holding right mouse button during boot/loading.
|
|
|
|
|
@StingRay,
Hi,
I try to help.... Because I have the same error with the v1.6
You can find my 3 reports in the Zone (A500 ACA500+,A 1200, WINUAE)
Best regards,
Pascal |
|
|
|
|
Here is the result form the debug slave:
1740 FF FE 00 00 F6
So on 1742 is $00
If I hold the right mouse button I GET the "SUPER" animation in this debug slave ! |
|
|
|
|
|
Same as Tom-Cat about The right mouse Button |
|
|
|
|
Thank you both for testing and feedback.
I have attached 3 new test slaves, does one of these fix the problem? If so, which one? |
|
|
|
|
Hi StingRay,
It's corrected each time... The word super appears
For me, the 3 slaves correct the problem in the same way...
There is no error message and there seem to be no operating differences (About speed or Graphics)...
I tried the 3 slaves on :
1) WINUAE(68030 NO MMU)
2) A1200 (68030 NO MMU @40 Mhz)
3) A500ACA500plus (68000 @28 Mhz)
Many Thanks,
Best Regards,
Pascal |
|
|
|
|
@StingRay,
At the same timee, I asked To Adaddon to create an Unofficial IPF from US Version.
I don't know if Your Slave already support the US version.
The IPF is in The Zone.
Maybe could You have a look too.
Many Thanks,
Pascal |
|
|
|
|
@StingRay,
It seems that Your Install & Slave 1.6 already support this US Version...
It's the same way here too with Your 3 Beta Slaves
Good Night,
Pascal |
|
|
|
|
Hi
Same here, all three new test slaves seem to work perfectly fine and also fix the "SUPER" bug :) |
|
SuperHangonDebug.slave (1,516) 2023-11-19 19:26